4.7★ · 29 Reviews
Stop Watching Your Hay Budget Hit the Stall Floor
The Pro Panel Stall Grazer® 3 in 1 Corner Feeder brings ground-level feeding to your stall — cutting hay waste, keeping forage up off the bedding, and holding grain, supplements, and salt in one corner where you left them. One-piece molded polyurethane. Made in the USA.
The Problem
Your Horse Is Eating From the Wrong Position — Every Single Day
It’s 5:30 in the morning, and you’re halfway through first feeding when you see it again: clean hay mixed through the shavings from the night before. Some is damp, some has been stepped on, and some is packed into the corner beneath your horse’s feet. You fork it into the wheelbarrow with the bedding, knowing part of the hay you paid for never became a meal. Then you replace it and move to the next stall.
Every horse owner who handles daily barn chores knows how quickly that routine becomes normal. Loose hay can migrate across the stall as your horse sorts, pulls, and drops each mouthful. A conventional elevated rack may contain the hay, but it also asks your horse to reach upward instead of eating with a naturally lowered head. Separate buckets for grain, supplements, and salt add more pieces to fill, check, clean, and keep in place.
The cost is more than the hay visible in the manure pile. Scattered forage adds material to every stall you clean, makes it harder to separate usable hay from soiled bedding, and leaves you wondering how much your horse actually consumed. Feed placed directly on the stall floor can mingle with shavings, dirt, or damp spots. When grain or supplements are tossed from an open container, measuring the ration accurately does little good if part of it ends up underfoot.
You shouldn’t have to choose between your horse’s natural feeding position and a cleaner, more organized stall. The real problem is the feeding setup: hay needs to stay contained and off the stall floor while remaining accessible at a comfortable, ground-level height, with the rest of your horse’s ration close at hand.
Every horse owner who handles daily barn chores knows how quickly that routine becomes normal. Loose hay can migrate across the stall as your horse sorts, pulls, and drops each mouthful. A conventional elevated rack may contain the hay, but it also asks your horse to reach upward instead of eating with a naturally lowered head. Separate buckets for grain, supplements, and salt add more pieces to fill, check, clean, and keep in place.
The cost is more than the hay visible in the manure pile. Scattered forage adds material to every stall you clean, makes it harder to separate usable hay from soiled bedding, and leaves you wondering how much your horse actually consumed. Feed placed directly on the stall floor can mingle with shavings, dirt, or damp spots. When grain or supplements are tossed from an open container, measuring the ration accurately does little good if part of it ends up underfoot.
You shouldn’t have to choose between your horse’s natural feeding position and a cleaner, more organized stall. The real problem is the feeding setup: hay needs to stay contained and off the stall floor while remaining accessible at a comfortable, ground-level height, with the rest of your horse’s ration close at hand.
Why It Keeps Happening
Wasted Hay. Wasted Money. A Horse That Deserves Better.
The problem isn’t you, and it isn’t your horse. Sorting forage, pulling out preferred stems, and shifting around while eating are ordinary behaviors. The frustration starts when the feeding equipment gives every dropped mouthful somewhere to scatter and provides no organized place for the rest of the ration.
An open pile on the floor offers little separation between hay and the bedding beneath it. Once your horse steps through that pile, urinates nearby, or pushes it into a damp corner, deciding what can be saved becomes another chore. A basic hay rack changes the location but may still leave you managing fallen stems below it. If the rack is installed high, your horse must reach up to eat rather than maintaining the lowered-head position encouraged by ground-level feeding.
Then the problem multiplies across the rest of the feeding station. Grain goes into one bucket, supplements into another container, and the salt block takes up space wherever it will stay put. Your horse can nose, tip, or move those pieces, leaving you to gather them before the next feeding. In a multi-stall barn, a few extra minutes spent removing hay from bedding, retrieving containers, and checking scattered feed become a noticeable part of every morning and evening routine.
That is the trap: each familiar option solves only one piece of the job. Floor feeding offers a low position but limited containment. An elevated rack contains hay but changes how your horse reaches it. Separate tubs organize grain or supplements but create more equipment. You are left assembling a feeding system from mismatched parts while still sweeping up the evidence that it is not working as neatly as it should.
An open pile on the floor offers little separation between hay and the bedding beneath it. Once your horse steps through that pile, urinates nearby, or pushes it into a damp corner, deciding what can be saved becomes another chore. A basic hay rack changes the location but may still leave you managing fallen stems below it. If the rack is installed high, your horse must reach up to eat rather than maintaining the lowered-head position encouraged by ground-level feeding.
Then the problem multiplies across the rest of the feeding station. Grain goes into one bucket, supplements into another container, and the salt block takes up space wherever it will stay put. Your horse can nose, tip, or move those pieces, leaving you to gather them before the next feeding. In a multi-stall barn, a few extra minutes spent removing hay from bedding, retrieving containers, and checking scattered feed become a noticeable part of every morning and evening routine.
That is the trap: each familiar option solves only one piece of the job. Floor feeding offers a low position but limited containment. An elevated rack contains hay but changes how your horse reaches it. Separate tubs organize grain or supplements but create more equipment. You are left assembling a feeding system from mismatched parts while still sweeping up the evidence that it is not working as neatly as it should.
- ✗Clean hay ends up mixed through the bedding by morning
- ✗Elevated racks ask your horse to eat with their head up
- ✗Grain tubs and salt blocks end up everywhere except where you put them
- ✗You are forking out feed you already paid for
The Solution
Feed the Way Nature Intended — Right in the Corner of Your Stall
The Pro Panel Stall Grazer® 3 in 1 Corner Horse Feeder brings those separate feeding jobs together in one ground-level unit. Its large center compartment holds several flakes of hay, and the feeding hole is sized for comfortable nibbling — so your horse works through the forage instead of dragging it across the stall. Keeping hay off the ground also keeps it out of the dirt and bedding underfoot.
Two smaller compartments flank the center. Use them for grain, supplements, or a salt block, depending on your horse's routine. Instead of hanging several buckets or hunting for a salt block your horse has nosed into a corner, everything has a defined place, and it is easier to see what is left after a feeding.
The build is straightforward: one piece of molded polyurethane, 46.5" x 34.63" x 28.53", 35 lbs., made in the USA. Because the footprint is substantial, measure your corner before ordering.
For your horse, forage stays accessible at a natural, ground-level height without sitting in the shavings. For you, it means a tidier feeding station and less loose hay to fork out with the bedding. It is a practical answer to an everyday barn problem, backed by equine expertise from a family-owned business trusted since 1948.
Two smaller compartments flank the center. Use them for grain, supplements, or a salt block, depending on your horse's routine. Instead of hanging several buckets or hunting for a salt block your horse has nosed into a corner, everything has a defined place, and it is easier to see what is left after a feeding.
The build is straightforward: one piece of molded polyurethane, 46.5" x 34.63" x 28.53", 35 lbs., made in the USA. Because the footprint is substantial, measure your corner before ordering.
For your horse, forage stays accessible at a natural, ground-level height without sitting in the shavings. For you, it means a tidier feeding station and less loose hay to fork out with the bedding. It is a practical answer to an everyday barn problem, backed by equine expertise from a family-owned business trusted since 1948.
🌿
Ground-Level Grazing
The ground-level design encourages the natural grazing habits your horse would use in a field — head down, eating from where forage actually sits.
🗂️
3-in-1 Feeding System
Center hay compartment plus two side compartments for grain, supplements, or salt blocks. One feeder handles your horse’s complete feeding routine.
🇺🇸
One-Piece USA Build
Molded from a single piece of polyurethane — one piece, no assembly. At 35 lbs. and 46.5" x 34.63" x 28.53", it is substantial without being a fixture. Proudly made in the USA.
🧹
Less Mess, Less Labor
The center feeding hole is sized for comfortable nibbling, which promotes less mess in the stall and keeps hay off the ground. Less wasted hay, less daily cleanup, more time with your horse.
Quick self-check
Is the Stall Grazer® Right for Your Barn?
What Riders Are Saying
★★★★★
"I absolutely love my stall grazers. The horses eat every bit of their hay or grain because they cannot flip any feed out of them. They have paid for themselves because no feed is wasted. I highly recommend them."
✓ Verified Buyer
★★★★★
"Love this! Great quality, fits perfectly. Will buy again."
✓ Verified Buyer
★★★★★
"Worth every penny. My horse is comfortable all season."
✓ Verified Buyer
Side by Side
Three Corner Feeders, Compared by Published Specifications
These products take different approaches to containing hay and grain in a stall corner. The table uses only specifications and features published by Schneiders or the respective manufacturers; information not published is marked “not listed.”
| Feature | Schneiders Pro Panel Stall Grazer® 3 in 1 Corner Horse Feeder | High Country Plastics CF-40 Corner Feeder | Behlen Country Poly Pro Corner Feeder |
|---|---|---|---|
| Published feeding configuration | Large central hay compartment plus two smaller side compartments | Main ground-feeder area plus grain or mineral inserts on each side | Steel hay rack above a one-piece poly tub |
| Published hay capacity | Several flakes | Not listed | 2–3 flakes |
| Material and construction | One-piece molded polyurethane | Impact-resistant, UV-protected poly with bolt-in side inserts | One-piece injection-molded poly tub with a 3/8-inch high-tensile steel hay rack |
| Published dimensions | 46.5 x 34.63 x 28.53 inches | 34 L x 57 W x 38 H inches | 35 H x 21 L x 21 W inches |
| Published weight | 35 lb | 52 lb | 22 lb |
| Separate side compartments or inserts | Two side compartments for grain, supplements, or salt blocks | Grain or mineral inserts on each side | No separate side compartments listed |
| Published placement or mounting information | Ground-level corner design for box stalls or outdoor settings | Ground feeder; mounts to wood stall walls or pipe panels with the specified bracket kit | Corner-mounted; mounting brackets included and installation height can be selected |
Everything Your Horse Needs. One Corner. Zero Mess.
The Pro Panel Stall Grazer® was designed from the ground up — literally — to give your horse a better way to eat. The one-piece molded polyurethane construction means there are no seams to harbor bacteria and no metal hardware to corrode. The generous 46.5" x 34.63" x 28.53" footprint fits any standard box stall corner, and at just 35 lbs it’s easy to position and reposition as needed. The center hay compartment accommodates several flakes at once; the sized feeding hole encourages your horse to nibble naturally rather than drag mouthfuls out and drop them. The two side compartments keep grain and supplements clean, contained, and off the ground. Professionals with million-dollar rides choose it. Vet clinics specify it. Horse owners who’ve used it don’t go back.
- ✓Ground-level corner design encourages natural grazing posture — head down, neck relaxed, airways clear (replace with product photo)
- ✓Large center hay compartment with sized feeding hole controls nibbling pace and dramatically reduces scatter waste
- ✓(2) side compartments for grain, supplements, or salt blocks — complete feeding station in a single corner unit
- ✓One-piece molded polyurethane construction — no seams, no rust points, no joint failures over time
- ✓46.5" x 34.63" x 28.53", weighs 35 lbs — fits standard box stall corners. Proudly made in the USA.
One Corner. Complete Feeding Station.
Warmth: Default Title
Size:
Color:
The Takeaway
If hay waste, stall mess, or unnatural feeding posture are real problems in your barn, this feeder pays for itself.
The Pro Panel Stall Grazer® 3 in 1 Corner Feeder is one of those products horse owners wish they’d found sooner. Ground-level design, three compartments, one-piece American-made construction — it’s a practical barn upgrade your horse will benefit from at every feeding.
Ready to Order?
Ready to Stop Wasting Hay and Start Feeding Right?
The Pro Panel Stall Grazer® 3 in 1 Corner Feeder is $269.95. Orders over $99 ship free — confirm shipping at checkout, since this is a large item and the cost depends on where it is going. Backed by Schneiders' Perfect Fit Guarantee. If it is not right for your horse's stall, we will make it right.
🚚 Free Shipping on $99+
↩️ Free Size Exchanges
🔒 Secure Checkout